Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 1500+ (1344.29-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x681  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400800<SYSCALL,MMX+,3DNow!+,3DNow!>
real memory  = 268369920 (255 MB)
avail memory = 248602624 (237 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 19:59:27)
acpi0: <AMIINT SiS735XX> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <SiS 735 host to AGP bridge> on hostb0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x8800-0x88ff mem 0xce000000-0xceffffff,0xcfeff000-0xcfefffff irq 11 at device 0.0 on pci1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
ohci0: <SiS 5571 USB controller> mem 0xcfffd000-0xcfffdfff irq 10 at device 2.2 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xcfffe000-0xcfffefff irq 5 at device 2.3 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
atapci0: <SiS 735 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 2.5 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pcm0: <SiS 7012> port 0xdc00-0xdcff,0xd400-0xd43f irq 10 at device 2.7 on pci0
pcm0: [ITHREAD]
pcm0: <C-Media Electronics CMI9738 AC97 Codec>
sis0: <SiS 900 10/100BaseTX> port 0xd000-0xd0ff mem 0xcfffc000-0xcfffcfff irq 10 at device 3.0 on pci0
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0a:e6:c8:48:e1
sis0: [ITHREAD]
sym0: <810> port 0xd800-0xd8ff mem 0xcfffff00-0xcfffffff irq 10 at device 13.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: [GIANT-LOCKED]
sym0: [ITHREAD]
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xcc00-0xccff mem 0xcffffe00-0xcffffeff irq 10 at device 15.0 on pci0
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:40:f4:bb:2e:d4
re0: [FILTER]
fwohci0: <VIA Fire II (VT6306)> port 0xc800-0xc87f mem 0xcffff000-0xcffff7ff irq 11 at device 17.0 on pci0
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:06:00:00:1f:cb:64
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:06:1f:cb:64
fwe0: Ethernet address: 02:11:06:1f:cb:64
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:11:06:00:00:1f:cb:64 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xfa70000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
uhci0: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 11 at device 19.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb2: <VIA 83C572 USB controller> on uhci0
usb2: USB revision 1.0
uhub2: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 11 at device 19.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb3: <VIA 83C572 USB controller> on uhci1
usb3: USB revision 1.0
uhub3: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xcffffd00-0xcffffdff irq 10 at device 19.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb4: EHCI version 0.95
usb4: companion controllers, 2 ports each: usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 4 ports with 4 removable, self powered
acpi_button0: <Sleep Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
fdc0: <floppy drive controller> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcffff pnpid ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
Timecounter "TSC" frequency 1344288152 Hz quality 800
Timecounters tick every 1.000 msec
hptrr: no controller detected.
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 19595MB <MAXTOR 6L020J1 A93.0500> at ata0-master UDMA100
ad1: 117246MB <Maxtor 6Y120P0 YAR41BW0> at ata0-slave UDMA100
acd0: DVDR <SONY DVD RW DRU-510A/1.0d> at ata1-master UDMA33
Waiting 5 seconds for SCSI devices to settle
(probe5:sym0:0:5:0): phase change 6-7 6@0148718c resid=4.
(probe5:sym0:0:5:0): phase change 6-7 6@0148718c resid=4.
(da0:sym0:0:5:0): phase change 6-7 6@0148718c resid=4.
da0 at sym0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 100 E.08> Removable Direct Access SCSI-2 device 
da0: 3.300MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad1s2a
plip0: [GIANT-LOCKED]
plip0: [ITHREAD]
ulpt0: at uhub3 port 1 (addr 2) disconnected
ulpt0: detached
WARNING: R/W mount of /ad0s1 denied.  Filesystem is not clean - run fsck
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: is alive again
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: is alive again
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: is alive again
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: not responding
nfs server home:/home: is alive again
drm0: <Rage XL AGP 2X> on vgapci0
info: [drm] AGP at 0xd0000000 64MB
info: [drm] Initialized mach64 1.0.0 20020904
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
acd0: FAILURE - READ_BIG MEDIUM ERROR asc=0x11 ascq=0x05 
GEOM_LABEL: Label for provider acd0t01 is iso9660/FreeBSD_Install.
nfs server home:/home: not responding
nfs server home:/home: is alive again
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 2 (addr 2) disconnected
ulpt0: detached
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 1 (addr 2) disconnected
ulpt0: detached
ulpt0: <Lexmark International Lexmark E120n, class 0/0, rev 2.00/1.00, addr 2> on uhub3
ulpt0: using bi-directional mode
ulpt0: at uhub3 port 1 (addr 2) disconnected
ulpt0: detached
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...2 2 0 2 2 2 0 0 0 0 done
All buffers synced.
Copyright (c) 1992-2007 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 6.2-RELEASE #0: Fri Jan 12 10:40:27 UTC 2007
    root@dessler.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 1500+ (1344.29-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x681  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400800<SYSCALL,MMX+,3DNow+,3DNow>
real memory  = 268369920 (255 MB)
avail memory = 253083648 (241 MB)
kbd1 at kbdmux0
ath_hal: 0.9.17.2 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
acpi0: <AMIINT SiS735XX> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <SiS 735 host to AGP bridge> mem 0xd0000000-0xd3ffffff at device 0.0 on pci0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <display, VGA> at device 0.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
ohci0: <SiS 5571 USB controller> mem 0xcfffd000-0xcfffdfff irq 10 at device 2.2 on pci0
ohci0: [GIANT-LOCKED]
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xcfffe000-0xcfffefff irq 5 at device 2.3 on pci0
ohci1: [GIANT-LOCKED]
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
atapci0: <SiS 735 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 2.5 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pcm0: <SiS 7012> port 0xdc00-0xdcff,0xd400-0xd43f irq 10 at device 2.7 on pci0
pcm0: <C-Media Electronics CMI9738 AC97 Codec>
sis0: <SiS 900 10/100BaseTX> port 0xd000-0xd0ff mem 0xcfffc000-0xcfffcfff irq 10 at device 3.0 on pci0
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0a:e6:c8:48:e1
sym0: <810> port 0xd800-0xd8ff mem 0xcfffff00-0xcfffffff irq 10 at device 13.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: [GIANT-LOCKED]
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xcc00-0xccff mem 0xcffffe00-0xcffffeff irq 10 at device 15.0 on pci0
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S media interface> on miibus1
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
re0: Ethernet address: 00:40:f4:bb:2e:d4
re0: [FAST]
fwohci0: <VIA Fire II (VT6306)> port 0xc800-0xc87f mem 0xcffff000-0xcffff7ff irq 11 at device 17.0 on pci0
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:06:00:00:1f:cb:64
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:06:1f:cb:64
fwe0: Ethernet address: 02:11:06:1f:cb:64
fwe0: if_start running deferred for Giant
sbp0: <SBP-2/SCSI over FireWire> on firewire0
fwohci0: Initiate bus reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
uhci0: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 11 at device 19.0 on pci0
uhci0: [GIANT-LOCKED]
usb2: <VIA 83C572 USB controller> on uhci0
usb2: USB revision 1.0
uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 11 at device 19.1 on pci0
uhci1: [GIANT-LOCKED]
usb3: <VIA 83C572 USB controller> on uhci1
usb3: USB revision 1.0
uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xcffffd00-0xcffffdff irq 10 at device 19.2 on pci0
ehci0: [GIANT-LOCKED]
usb4: EHCI version 0.95
usb4: companion controllers, 2 ports each: usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 4 ports with 4 removable, self powered
acpi_button0: <Sleep Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: model IntelliMouse, device ID 3
fdc0: <floppy drive controller> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FAST]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
ppc0: <ECP parallel printer port> port 0x378-0x37f,0x778-0x77b irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1344289259 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 19595MB <MAXTOR 6L020J1 A93.0500> at ata0-master UDMA100
ad1: 117246MB <Maxtor 6Y120P0 YAR41BW0> at ata0-slave UDMA100
acd0: DVDR <SONY DVD RW DRU-510A/1.0d> at ata1-master UDMA33
Waiting 5 seconds for SCSI devices to settle
(probe5:sym0:0:5:0): phase change 6-7 6@0f6bd38c resid=4.
da0 at sym0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 100 E.08> Removable Direct Access SCSI-2 device 
da0: 3.300MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
(da0:sym0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:sym0:0:5:0): CAM Status: SCSI Status Error
(da0:sym0:0:5:0): SCSI Status: Check Condition
(da0:sym0:0:5:0): NOT READY asc:3a,0
(da0:sym0:0:5:0): Medium not present
(da0:sym0:0:5:0): Unretryable error
Opened disk da0 -> 6
(da0:sym0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:sym0:0:5:0): CAM Status: SCSI Status Error
(da0:sym0:0:5:0): SCSI Status: Check Condition
(da0:sym0:0:5:0): NOT READY asc:3a,0
(da0:sym0:0:5:0): Medium not present
(da0:sym0:0:5:0): Unretryable error
Opened disk da0 -> 6
(da0:sym0:0:5:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
(da0:sym0:0:5:0): CAM Status: SCSI Status Error
(da0:sym0:0:5:0): SCSI Status: Check Condition
(da0:sym0:0:5:0): NOT READY asc:3a,0
(da0:sym0:0:5:0): Medium not present
(da0:sym0:0:5:0): Unretryable error
Opened disk da0 -> 6
Trying to mount root from ufs:/dev/ad1s1a
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...3 3 0 3 3 3 0 0 0 done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
All buffers synced.
Copyright (c) 1992-2008 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
	The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 7.0-RELEASE #0: Sun Feb 24 19:59:52 UTC 2008
    root@logan.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Athlon(tm) XP 1500+ (1344.29-MHz 686-class CPU)
  Origin = "AuthenticAMD"  Id = 0x681  Stepping = 1
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
  AMD Features=0xc0400800<SYSCALL,MMX+,3DNow!+,3DNow!>
real memory  = 268369920 (255 MB)
avail memory = 248602624 (237 MB)
kbd1 at kbdmux0
ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
hptrr: HPT RocketRAID controller driver v1.1 (Feb 24 2008 19:59:27)
acpi0: <AMIINT SiS735XX> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
agp0: <SiS 735 host to AGP bridge> on hostb0
pcib1: <PCI-PCI bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
vgapci0: <VGA-compatible display> port 0x8800-0x88ff mem 0xce000000-0xceffffff,0xcfeff000-0xcfefffff irq 11 at device 0.0 on pci1
isab0: <PCI-ISA bridge> at device 2.0 on pci0
isa0: <ISA bus> on isab0
ohci0: <SiS 5571 USB controller> mem 0xcfffd000-0xcfffdfff irq 10 at device 2.2 on pci0
ohci0: [GIANT-LOCKED]
ohci0: [ITHREAD]
usb0: OHCI version 1.0, legacy support
usb0: <SiS 5571 USB controller> on ohci0
usb0: USB revision 1.0
uhub0: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
uhub0: 3 ports with 3 removable, self powered
ohci1: <SiS 5571 USB controller> mem 0xcfffe000-0xcfffefff irq 5 at device 2.3 on pci0
ohci1: [GIANT-LOCKED]
ohci1: [ITHREAD]
usb1: OHCI version 1.0, legacy support
usb1: <SiS 5571 USB controller> on ohci1
usb1: USB revision 1.0
uhub1: <SiS OHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
uhub1: 3 ports with 3 removable, self powered
atapci0: <SiS 735 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xff00-0xff0f at device 2.5 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pcm0: <SiS 7012> port 0xdc00-0xdcff,0xd400-0xd43f irq 10 at device 2.7 on pci0
pcm0: [ITHREAD]
pcm0: <C-Media Electronics CMI9738 AC97 Codec>
sis0: <SiS 900 10/100BaseTX> port 0xd000-0xd0ff mem 0xcfffc000-0xcfffcfff irq 10 at device 3.0 on pci0
miibus0: <MII bus> on sis0
rlphy0: <RTL8201L 10/100 media interface> PHY 1 on miibus0
rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0a:e6:c8:48:e1
sis0: [ITHREAD]
sym0: <810> port 0xd800-0xd8ff mem 0xcfffff00-0xcfffffff irq 10 at device 13.0 on pci0
sym0: No NVRAM, ID 7, Fast-10, SE, parity checking
sym0: [GIANT-LOCKED]
sym0: [ITHREAD]
re0: <RealTek 8169S Single-chip Gigabit Ethernet> port 0xcc00-0xccff mem 0xcffffe00-0xcffffeff irq 10 at device 15.0 on pci0
miibus1: <MII bus> on re0
rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus1
rgephy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
re0: Ethernet address: 00:40:f4:bb:2e:d4
re0: [FILTER]
fwohci0: <VIA Fire II (VT6306)> port 0xc800-0xc87f mem 0xcffff000-0xcffff7ff irq 11 at device 17.0 on pci0
fwohci0: [FILTER]
fwohci0: OHCI version 1.0 (ROM=1)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 00:11:06:00:00:1f:cb:64
fwohci0: Phy 1394a available S400, 3 ports.
fwohci0: Link S400, max_rec 2048 bytes.
firewire0: <IEEE1394(FireWire) bus> on fwohci0
fwe0: <Ethernet over FireWire> on firewire0
if_fwe0: Fake Ethernet address: 02:11:06:1f:cb:64
fwe0: Ethernet address: 02:11:06:1f:cb:64
fwip0: <IP over FireWire> on firewire0
fwip0: Firewire address: 00:11:06:00:00:1f:cb:64 @ 0xfffe00000000, S400, maxrec 2048
sbp0: <SBP-2/SCSI over FireWire> on firewire0
dcons_crom0: <dcons configuration ROM> on firewire0
dcons_crom0: bus_addr 0xfa70000
fwohci0: Initiate bus reset
fwohci0: BUS reset
fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
uhci0: <VIA 83C572 USB controller> port 0xc000-0xc01f irq 11 at device 19.0 on pci0
uhci0: [GIANT-LOCKED]
uhci0: [ITHREAD]
usb2: <VIA 83C572 USB controller> on uhci0
usb2: USB revision 1.0
uhub2: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
uhub2: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 11 at device 19.1 on pci0
uhci1: [GIANT-LOCKED]
uhci1: [ITHREAD]
usb3: <VIA 83C572 USB controller> on uhci1
usb3: USB revision 1.0
uhub3: <VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
uhub3: 2 ports with 2 removable, self powered
ehci0: <VIA VT6202 USB 2.0 controller> mem 0xcffffd00-0xcffffdff irq 10 at device 19.2 on pci0
ehci0: [GIANT-LOCKED]
ehci0: [ITHREAD]
usb4: EHCI version 0.95
usb4: companion controllers, 2 ports each: usb2 usb3
usb4: <VIA VT6202 USB 2.0 controller> on ehci0
usb4: USB revision 2.0
uhub4: <VIA EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb4
uhub4: 4 ports with 4 removable, self powered
acpi_button0: <Sleep Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
fdc0: <floppy drive controller> port 0x3f2-0x3f3,0x3f4-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio0: [FILTER]
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
sio1: [FILTER]
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xcffff pnpid ORM0000 on isa0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/16 bytes threshold
ppbus0: <Parallel port bus> on ppc0
ppbus0: [ITHREAD]
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ppc0: [GIANT-LOCKED]
ppc0: [ITHREAD]
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 1344287909 Hz quality 800
Timecounters tick every 1.000 msec
hptrr: no controller detected.
firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
firewire0: bus manager 0 (me)
ad0: 19595MB <MAXTOR 6L020J1 A93.0500> at ata0-master UDMA100
ad1: 117246MB <Maxtor 6Y120P0 YAR41BW0> at ata0-slave UDMA100
acd0: DVDR <SONY DVD RW DRU-510A/1.0d> at ata1-master UDMA33
Waiting 5 seconds for SCSI devices to settle
(probe5:sym0:0:5:0): phase change 6-7 6@0126df8c resid=4.
(probe5:sym0:0:5:0): phase change 6-7 6@0126df8c resid=4.
(da0:sym0:0:5:0): phase change 6-7 6@0126df8c resid=4.
da0 at sym0 bus 0 target 5 lun 0
da0: <IOMEGA ZIP 100 E.08> Removable Direct Access SCSI-2 device 
da0: 3.300MB/s transfers
da0: Attempt to query device size failed: NOT READY, Medium not present
Trying to mount root from ufs:/dev/ad1s2a
plip0: [GIANT-LOCKED]
plip0: [ITHREAD]